1/18th Scale Mi-24 Hind Will Become A Reality !!!

Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
I have been working on the winglets ALL WEEK LONG and am still not finished .

The leading edge of the winglet is a week spot so I do not think that I can make a secondary access door there . But I think that I have it worked out.

I plan to make the turtle deck removable so you can have access through the top !!

There are several location that the screw heads can me hidden .

I will raise the ceiling ( for figure head room ) and make it screw down as well , then come on top of that with the turtle deck.

The main rotor will have a 2-3 inch brass shaft so that will come off as well.

I am also trying to design the whole main cabin screw together because there will be a lot of stuff in there to align and get right before sealing it up .

So screw together may just be the way to go .

The dark gray top piece will be removable


 
daremo

daremo

Officer III
Sep 12, 2011
1,064
2
0
That is a beast! You need to stick a figure next to it just to give it a sense of scale. I can tell it's huge but it would be cool to see it dwarf a figure.
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
5 days working on the wing stbs and I am not done yet. Probably another 2 or 3 and I will have them wrapped up.

Next I will start working on the landing gear.

Setting the anhedral .










 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Thanks Eddie and guys .

Does anybody know when were and at what time the Russians started and stopped using the Russian star on the belly of the Hind ?
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Thanks Guys

Moving right along I have mounted the front gear. It will have to function because the wheel and strut are visable when retracted.

The main gear will be plug and play and will be static.







 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Thanks Maritime !!

Got here up on her feet !! Lots of work for these small steps. I almost have the gear ready to ship to get them casted in metal.

Rotor update . I made a skeleton of the rotor hub out of brass and used some kind of JB type epoxy to hold it together . Failer I am kicking around the idea of having the rotor cast in metal as well . Or if the cost is sky high I will try to soldier the brass inner skeleton .

I have made casts of the blade with a brass tube cast inside of it and hand them outstretched fo about a week. The blade sagged at about the half way point on the blade at about a half inch . I have made the blades so they can be tunred upside down to bring them back or simply bend the blade back into shape.

pics of installed gear.





 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
pvanroy wrote:

Beautiful work!

Actually, I don't think they ever stopped using the star on the underside - even the latest Mi-24PN/Mi-35M, Mi-28 and Ka-52 helicopters have the star on the underside (although the new VVS markings introduced in 2010 now feature a thin white and blue trim to the star instead of simply white as used previously).


Thanks for that info . The belly star will be provided :D :D :D

At this point she is a major tail dragger . Let us see with all the rotors and interior if her tail comes up.

But I think not. I see some lead shot in her nose in the future to keep her nose down.

If I do it now I fear that she will snap her gear struts . So I need to try once her new metal gear is on.

About 3 weeks to get the metal gear.
_________________
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Hey Guys time for a semi update .
My real work took a turn for the better and that takes priority over everything.
I also have almost cleared out my back orders of kits and only have 2 more full build HUMVEES to finish. Hopefully this weekend.

Then it is back to the Hind .
I am still having issues with the main rotor hub that need to be worked out . I need to try at least 3 experaments on the core support to see what will be the best support.

I have received the nose arrangements and they look fantastic !!!
Jay has done it again !!
No time yet for pics but the parts and front gattling gun look perfect.
The gun will swivel and levitate !!

The Crocodile now has it's teeth !!!


As far as pilots go , the Russian pilots used a jump suit similar to plain grey overalls ( Mikael Myers ) and a 60 era crash helmet similar to the American helmet . Looking like a Bell type motorcycle helmet. So I will make the helmet but you guys will supply the figure having to only paint their clothing a dark to light gray .

Simple !!!



[/quote]
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
azslogan said:
Check out this Hind...

Vet?elec v oblac?ch. ?e?i vyslali na cvi?en? NATO d?monick? bitevn?k - iDNES.cz
Click to expand...


Totally cool Hind !!!

I did get something done and we are moving in the right direction. Hopefully I got things worked out with the metal caster . He can cast silicon tubes in the rotor hub which will make the blades set up that I did , work !!! He should get the rotor hub Monday.

I also solved my issue with the landing gear . I was losing time and hair ( by pulling it out ) trying to make the connections like the kit . I canned that idea and will make it screw in to the wheel wells. That way if needed they can be adjusted . The landing gear will ship Monday.

He is not sure if he will use non lead pewture or zinc as the metal . He said the zinc will be stronger and cheaper.
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Zinc it will be .

I have been working on the interior and it looks like I can keep the floor in the rear cabin as is but I need to raise the ceiling.

As I stated before it will be near impossible to set up figures through the cargo hatch so I am designing the turtle deck to be removable .

I almost have the cockpit mounted and have noticed a problem .

The gunners seat is about 1/2 of an inch thick . This makes the gunners head ( depending on the figure ) stick up and out of the bubble canopy . I can cut off about 1/4 - 1/38 of an inch off of the bottom of the seat . This may not be enough for the figure to sit inside of the glass . So there is a good chance that you all will have to sand or shave the figure's ( seated ) back theighs and kiester to get him low enough.

It look likes the pilot will be fine but I am not 100% sure of this .
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
I have sent the main rotor and landing gear to the caster. The landing gear is no problem but we are going back and forth on the rotor. I may have to cut all of the arms off of the rotor and make them so they bolt onto the stub. Kind of like the real one .

I will talk to the decal /sticker stencil guy today or Wends. to see how they are coming along.

I have just spent 6 full days on the Hind and will spend most of the week working on it as well. I have spent a whole day trying to mount the door to the frame and canopy . These little details take so much time with nothing to really show. :? :? :?
The door hinge has proven to be perplexing . Then I have to design the hinge for the WSO canopy hatch .

Progress with no picks

canopy 90% mounted
cockpit 95% mounted
door 90% mounted.

After those are done I need to rework the pass through from pilot's seat to rear cabin .I have the floor worked out in the crew cabin . There was usually a rubber mat used on the floor . What do you think of me using the diamond anti skid plate on it ?

I have the doors cut out along with the windows in the crew cabin.

Input needed........Input needed.........Input needed

1. What do you guys think of me using diamond anti skid on the floor in the crew cab ?

2. Once I get the canopy all worked out and mounted. It will be EXTREAMLY DIFFICULT to insert the pilot and WSO figures so I am thinking of trying to make the canopy and frame " click " into place . A good bit of engineering will have to be done to get this to work.
I have already cut out holes to allow the figures' feet to fit in.
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Updated price tag on the Hind

R and D books --------------------------------------$ 100
3 x 1/35 Trumpeter kits ----------------------------$280
3-D printing cockpit ----------------------------------$240
3-D printing canopies ---------------------------------$100
3-d printed sensor, rocket pod intake and filter-----$55
3-d printing large piece in progress ------------------$ 450
Rear rotor and main rotor hub -------------------------$190
Exaust nozzels ------------------------------------------$ 15
Paint -----------------------------------------------------$100
Nose sensors and armament---------------------------$85
Canopy plug ------------------------------------------$126

Total--------------------------------------------------$1,741

Est price on metal parts $200-$300 :?


:D These guys have kept this project afloat !!

At this time almost half of the supporters are off of the 1/18th forums :shock: :shock: :shock:

Thanks :D :D

YT
PVANROY
SALTYMARINE
LEE PATERSON------------Full Build !! The first !!
BLACK DRAGON ONE
COREY-D
TOM EDWARDS X 2 ---2 full builds !!
KERRY MOZINGO
SLOGAN-----------------Full build !!
ROBBIE PIERCE
MORGUHN
JORGE BAHAMONDE X 2 !!
Jay !!!
Daremo


16 kits !!!

Still a little time to go , but now is the time to get in on the $300 presale ( shipping added later )


_________________
 
saltymarine

saltymarine

Enlisted
Aug 22, 2011
270
23
18
I'm still here, just workin 80 hrs a week last 7 months, it's the Drive by bid season right now, people call and ask" what's a ball park price for a 37 x 18 deck," I say $35,000, they say when can you start, it's crazy !!! The economy is ready to crash in 6 months to a year, it's a 10 year cycle I've seen 4 times now, so I'm riding the gravy train till it bursts, get ready to buy real estate soon !!!
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
saltymarine said:
I'm still here, just workin 80 hrs a week last 7 months, it's the Drive by bid season right now, people call and ask" what's a ball park price for a 37 x 18 deck," I say $35,000, they say when can you start, it's crazy !!! The economy is ready to crash in 6 months to a year, it's a 10 year cycle I've seen 4 times now, so I'm riding the gravy train till it bursts, get ready to buy real estate soon !!!
Click to expand...

80 hrs a week ?

YIKES !!!!!!!

Finally a few progress pics .










 
G.I.*EDDIE

G.I.*EDDIE

gobbles a LOT of cock
Founder
Mar 14, 2011
43,432
428
83
S.E. Mich :(
 
Pickelhaube

Pickelhaube

Replicator of Toys
Officer Club
Mar 15, 2011
1,601
124
63
65
New Orleans
Thanks guys it means a lot !!!!

BTW

After fitting everything together it does NOT sit on it's tail !!!

But after molding and maybe cutting in the resin flow channels that could change.

But for now she sits just fine !!!

_________________











[/QUOTE]
 
A

azslogan

Officer
Mar 14, 2013
384
16
18
Seeing this finished and painted is going to make for an amazing moment. I'd like to see this next to a Blackhawk as well.
 
You must log in or register to reply here.
Top Bottom